DSE Products

- - DSEUltra
  - - DSE701
    - DSE702
    - DSE703
    - DSE704
    - DSE705
    - DSE710
    - DSE720
    - DSE4110
    - DSE4120
    - DSE4130
  - DSEControl
  - - DSE5110
    - DSE5120
    - DSE5210
    - DSE5220
    - DSE5310
    - DSE5320
    - DSE7210
    - DSE7220
    - DSE7310
    - DSE7320
  - DSEPower
  - - DSE5510
    - DSE5520
    - DSE5560
  - DSEMarine
  - - DSE5310M
    - DSE5510M
  - DSEExtra
  - - DSE123
    - DSE130
    - DSE157
    - DSE545
    - DSE548
    - DSE549
    - DSE810
    - DSE5103
    - DSE5105
    - DSE9120
    - DSE9130
    - DSE9150
    - DSE9240
    - DSE9250
  - DSENet
  - - DSE2130
    - DSE2157
    - DSE2548
  - Other Products
  - - DSE103
    - DSE402
    - DSE500
    - DSE501
    - DSE509
    - DSE511
    - DSE512 (OBSOLETE)
    - DSE520
    - DSE521
    - DSE530
    - DSE540
    - DSE541
    - DSE550
    - DSE555
    - DSE556
    - DSE557
    - DSE560
    - DSE808
    - DSE820
    - DSE4210 (OBSOLETE)
    - DSE5110 BC

- View 1
- View 2
- View 3
DSEMarine
DSE5510M
Auto Start Control Module - DNV Certified (Electronic Engine enabled)
The DSE5510M is an Automatic Engine Control Module, designed to provide advanced load share functionality for diesel and gas generating sets that include non-electronic and electronic engines. The module also provides excellent engine monitoring and protection features. The modules load share functions include, automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s). The module has been designed to combine a maximum of 16 generators and 16 mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4 mains (utility) supplies (DSE5560 required to synchronise with the mains) The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.

Downloads
T (Translations)

Certificates PDF
Diagrams ( PDF )

Instructions PDF
DataSheet ( A4 / US )

Further Information

Main Features	Electronic engine capability RS232 or RS485 remote communications Modbus RTU Pin number protected front panel programming Engine exercise timer Back-lit LCD 4-line text display Multiple language options Voltage measurement Configurable inputs (9) Configurable outputs (5) Automatic start Manual start Audible alarm LED indicators Built-in governor and AVR control Engine history event log Engine protection Fault condition notification to a designated PC Front panel mounting PC configuration Mains (utility) failure detection Configurable alarm timers Configurable start & stop timers Automatic load transfer SMS alert messaging Multi-set communications Front panel mounting Remote monitoring Magnetic pick-up Load Share Features Automatic starting & stopping of generator on load demand Automatic hours run balancing of generator sets Dead bus sensing Module has the ability to interface with existing load share systems Direct communication from the module to the governor and AVR Volts & frequency matching KW and Kvar load sharing with multiple generators ROCOF & vector shift
Benefits	Sends SMS messages to engineers to notify specific engine problems (GSM Modem & SIM Card required) On-site and remote module configuration In-built engine diagnostics removes the requirement for service equipment Full engine protection & instrumentation without the need for additional senders (Electronic engines only) Remote monitoring of the module using comprehensive DSE PC software License free PC software
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO and START pushbuttons. Three of these push buttons include an LED indicator. Additional pushbuttons provide LCD display scroll, lamp test, mute functionality and breaker control.
Important Notes	THIS MODULE IS A SPECIAL MARINE VERSION FULLY CERTIFIED BY DNV FOR USE ON-BOARD VESSELS. THE 'STANDARD' DSE5510 CANNOT BE USED FOR MARINE APPLICATIONS AS IT HAS NOT BEEN CERTIFIED. Below are links to some helpful documents regarding synchronisation and load sharing : Load Share System Design and Commissioning Guide Guide to Synchronising and load sharing part 1 Guide to Synchronising and load sharing part 2 Below is a link to a helpful document regarding electronic engines : Electronic engines and DSE Wiring
Alternative / Associated Products	DSE123 - Load Share Lines Interface DSE5310M - Auto Start Control Module - DNV Certified (Electronic engine enabled)