DSE Product Range

The DSE123 is a Load Share Lines Interface Device designed to expand existing analogue load share systems. The DSE123 monitors existing load share lines and converts the analogue information into a digital format. This process allows all existing control modules to communicate with the DSE5510 control modules when they are added to the system.   When DC power is applied to the interface device a status LED will illuminate. If the DSE123 cannot communicate with the DSE5510, the LED will flash to indicate a communication malfunction.   The device has been designed to work with both DSE and other manufacturers existing load share systems, providing that the system is being expanded with a DSE5510.

The DSE130 is an input expansion system used to provide modules within the DSEControl® and DSEPower® Series (excluding the DSE51xx & DSE52xx) with additional analogue and digital input capabilities. 

The DSE157 is an output relay expansion module for use with DSEControl® and DSEPower® Series Modules (excluding DSE51xx). The DSE157 has been designed to extend a host modules output capabilities. The additional capabilities allow OEM’s to meet increasingly complex industry specifications. The module incorporates ‘DIN’ rail mountings and an interconnecting FCC 68 cable, allowing quick fixing into a panel. The module will work up to 50 meters from the host control module.

The DSE545 is an LED expansion module for modules within the DSEControl® (Excluding the DSE51xx) and DSEPower® Series. The module has been designed to display a maximum of eight local or remote individual LED indications up to a distance of 50 meters.  

The DSE545 is presented in a horizontal enclosure.

The DSE548 is an LED expansion module for modules within the DSEControl® (Excluding the DSE51xx) and DSEPower® Series. The modules have been designed to display a maximum of eight local or remote individual LED indications up to a distance of 50 meters.   The DSE548 is presented in a vertical enclosure.

The DSE549 Remote Annunciator has been designed to be connected to the DSE130 input expansion module. It provides 16 LED indicators an alarm sounder, mute button and an LED test button.

The DSE810 PC Configuration Interface is designed for use with the DSEControl and DSEPower Series and the DSE710 and DSE720.  It has been designed to be used in conjunction with the DSE5xxx, DSE5xx, DSE4200 series and 710/720 series configuration software and also Link5000Plus communication software.  The interface enables the user to access the configuration settings stored within the module, to allow changes to be made.

The interface kit is made up of:

USB Version     

The DSE9120 is a 7.3 Amp battery charger suitable for 12 Volt lead-acid batteries. 

The charger has been designed to be permanently connected to automotive batteries, keeping them charged to their maximum capacity. The chargers can also be used to supply a standing load that is attached to a battery. To improve reliability the chargers do not include any moving parts. The technology inside the chargers has been designed to avoid overcharging and overloading. The chargers will also continue to operate during cranking and running and have the ability to accept multiple AC voltage connections.

The DSE9240 is 3.5 Amp battery charger suitable for 24 Volt lead-acid batteries.

• Lightweight
• Compact design
• Can remain operational during engine cranking and running 
• Suitable for connection to a wide range of AC voltages between 100V and 240V, 50Hz or 60Hz.  
• No moving parts
• Switch mode design
• Overload & short circuit protection
• LED charging indicator
• Convection cooling
• Minimum 80% efficiency throughout full operating range

The DSE5103 is a 3 Amp 12/24 Volt Battery Charger.  It is designed to be permanently connected to automotive batteries, maintaining them in a fully charged condition without overcharging.  The charger is also capable of rapidly recharging batteries at a current up to the full rated output.  The charger may also be used to supply a standing load attached to the battery.  The charger output may be factory set to account for the standing load.

The charger is designed for reliability, ease of installation and accessibility during routine servicing.  It features radio frequency suppression and its smooth output linear mode design has a low voltage making the charger suitable for use with electronic equipment.

The DSE5105 is a 5 Amp 12/24 Volt Battery Charger.  It is designed to be permanently connected to automotive batteries, maintaining them in a fully charged condition without overcharging.  The charger is also capable of rapidly recharging batteries at a current up to the full rated output.  The charger may also be used to supply a standing load attached to the battery.  The charger output may be factory set to account for the standing load.

The charger is designed for reliability, ease of installation and accessibility during routine servicing.  It features radio frequency suppression and its smooth output linear mode design has a low voltage making the charger suitable for use with electronic equipment.

The 2 Amp Battery Charger has been designed to be permanently connected to batteries, keeping them charged to their maximum capacity. 

The charger can be either mounted via DIN Rail or to the Chassis, using the fixing holes that are built into the case.  The chargers stylish design includes an LED indicator on the front that shows when the charger is  in a normal or overload condition. 

To improve reliability the charger does not include any moving parts.  it will continue to operate during cranking and running.  The charger can also accept multiple AC voltage connections

The 5 Amp Battery Charger has been designed to be permanently connected to batteries, keeping them charged to their maximum capacity. 

The charger can be either mounted via DIN Rail or to the Chassis, using the fixing holes that are built into the case.  The chargers stylish design includes an LED indicator on the front that shows when the charger is  in a normal or overload condition. 

To improve reliability the charger does not include any moving parts.  it will continue to operate during cranking and running.  The charger can also accept multiple AC voltage connections

The 3.7 Amp Battery Charger has been designed to be permanently connected to batteries, keeping them charged to their maximum capacity. 

The charger can be either mounted via DIN Rail or to the Chassis, using the fixing holes that are built into the case.  The chargers stylish design includes an LED indicator on the front that shows when the charger is  in a normal or overload condition. 

To improve reliability the charger does not include any moving parts.  it will continue to operate during cranking and running.  The charger can also accept multiple AC voltage connections